Reptile Heat Controllers

Zilla Temperature Controllers make it easy to maintain a consistent temperature in your reptile terrarium. An simple dial lets you set the desired temperature (between 60°-105°F), and the controller will automatically regulate your heating device to keep that temperature constant.

• Controls heating devices automatically
• Helps maintain consistent terrarium temperature
• Maintains preset temperature from 60°-105°F

The controller is easy to use: just place the temperature probe inside the habitat and plug in a heat source such as an incandescent dome (up to the wattage of the Temperature Controller), set the temperature you want, and that's it! The Temperature Controller will automatically turn the heat source on and off to maintain a consistent temperature. An internal safety regulator will automatically shut off the heat source at 110°F to prevent dangerous overheating.

Note: Not for use with heat rocks. Heat source not included.

Zoo Med Repti Temp Rheostat - For manual heat control. With a turn of the knob, you can adjust the temperature of most non-thermostatically controlled heating devices! Plug in up to 2 compatible heating items with a combined wattage of up to 150 watts!

• Provides manual heat control
• Simple operation
• For use with most reptile heating devices

Turn your heaters up in the winter and down in the summer depending on your inside house temperatures! Great for use with Zoo Med's Repticare Rock Heater, Ceramic Heat Emitters, ReptiTherm Under Tank Heaters, incandescent heat bulbs (up to 150 watts) as well as other reptile heat devices.

For use with:

• Reptile rock heaters
• Reptile heat caves
• Reptile heat pads or under tank heaters
• Reflector spot bulbs
• Infrared spot bulbs
• Ceramic heat emitters
• All other types of reptile heat lamps up to a total of 150 watts maximum

1-year manufacturer warranty.

FAQ:
Q: What is the difference between a rheostat and a thermostat?
A: A rheostat is basically a dimmer. It allows you to manually reduce the amount of power reaching a heater. A thermostat like the 500R senses the temperature and turns the heater on and off accordingly.
Q: Can I use the rheostat/thermostat with a Reptisun, Avian Sun or Power Sun UV?
A: These lamps need specific line voltages; they cannot be used with dimmers/rheostats.
Q: How many heating devices can be controled with this device?
A: You can plug up to two heating devices into this temperature controller. Make sure the maximum wattage capability is not exceeded.
Q: I am using a thermostat/rheostat and the temperature is not rising.
A: Thermostats and rheostats cannot increase the temperature a heat source is capable of putting out. Setting the thermostat/rheostat to the maximum temperature/ level will be as hot as the heat source itself will get.

The Zoo Med Reptitemp Digital Thermostat allows you to maintain precise control of your terrarium temperature with an easy-to-program LCD interface. Just plug in your heating device (up to 600 watts) or cooling device (up to 150 watts), set the desired temperature and mode, and let the Reptitemp handle the rest!

• Controls and maintains proper terrarium temperature
• Easy to program with LCD display and 2-button operation
• Built in memory stores settings in case of power failure
• Use to control heating or cooling devices

The Reptitemp Thermostat controls temperature by turning on heating devices in "Heat" mode or by turning on cooling devices (such as a fan) in "Cool" mode. When the tank temperature strays above or below the set temperature, the Reptitemp will activate the device to raise or lower temperature until it returns to the proper level. An alarm feature may be enabled to alert you when the temperature is above or below the programmed settings.

Installation: Position the sensor inside the terrarium. A suction cup is provided for attachment to habitat walls. Keep the control unit outside the terrarium for easy access to controls. Hook and loop fasteners are included for easy attachment to outside walls. Plug in the Reptitemp, program your desired settings, and plug in your heating/cooling device, making sure the device is switched on.

Note: The Reptitemp Thermostat may only be used with ONE heating/cooling device at a time.

Specifications:
600 W max resistive load
Heating units: 600 W max
Cooling units: 150 W max
Remote temperature sensor cable: 6' (185 cm)
Temperature control range: 50F-122F (10C-50C)
1 year manufacturer warranty